Axion RGBW LED Spot Lights
Axion RGBW LED Spot Lights - Image 2
Axion RGBW LED Spot Lights - Image 3
Axion RGBW LED Spot Lights - Image 4
Axion RGBW LED Spot Lights - Image 5
Axion RGBW LED Spot Lights - Image 6
Axion RGBW LED Spot Lights - Image 7
Axion RGBW LED Spot Lights - Image 8
Axion RGBW LED Spot Lights - Image 9
Axion RGBW LED Spot Lights - Image 10
Axion RGBW LED Spot Lights - Image 11
Axion RGBW LED Spot Lights - Image 12

Axion RGBW LED Spot Lights

Price range: $49.00 through $99.00

RGBW LED high efficiency surface mount weatherproof fixtures controllable using our DMX Controller, DMX Decoder or any 24V compatible product. Outdoor stake mounts also available.

- +
SKU: N/A Categories: ,

The Axion Lighting RGBW spotlight series gives you full control over all colors in a living space or outdoor setting. Great for accenting artwork, unique wall textures, outdoor buildings, trees, and more. IP67 rated so it’s also perfect for indoor or outdoor use. Leveraging these fixtures and our robust DMX Controller along with DMX Decoders you can create a whole house indoor and outdoor system that is low voltage, dimmable, easily integrates with popular control system platforms, and gives you millions of colors and temperatures to set the perfect ambiance.

Installation is simple with the included round base. Optionally, if installing outdoors you can purchase one of the landscape stake mounts. Simply connect the RGBW color wires to your DMX decoder like you would any other linear light strip.

 3 Watt15 Watt
Voltage24 volts
Wattage3 watts15 watts
Total Lumen Output30 lumen1000 lumen
White Temperature3000 Kelvin
Dimensions42mm diameter x 75mm tall, 85mm with base75mm diameter x 100mm tall, 85mm with base
Beam Angle30 degrees
Weather RatingIP67 – Protection against contact with objects greater than 1mm in diameter.
Protected against short periods of immersion in water while under pressure between 15cm and 1m.
Operating Temperature
-20℃ ~ +60℃
Warranty3 Years
Lifetime in Hours50,000 hours continuous use
 
Weight N/A
Dimensions N/A
Size

3 Watt, 15 Watt

Installation Instructions

Installation Requirements

  • Before you begin installation, please verify that 24-volt power is off. It is recommended you disconnect the power supply before starting.
  • Although this document does not cover the power supply or system integration, it is worth noting that all dimming happens on the DC output side and these low voltage fixtures should not be hooked up to a 120V or 220V dimmer.
  • Do not hold the fixture by the RGBW+ cable.
  • Please check the contents of the package before installation for damage.
  • We recommend bench testing before installation.
  • ALL WIRING AND INSTALLATION SHOULD ADHERE TO LOCAL AND NATIONAL WIRING STANDARDS.

Safety

  • The fixture is 24VDC; connecting it to 12VDC, 120/240/220 AC will void the warranty and cause permanent damage.
  • Do not wire the fixture into a DMX decoder or power supply that is energized.
  • All dimming happens on the 24V side and should be done with a compatible PWM device.
  • Do not install in an environment that is fully sealed. The heat sink must have airflow to properly cool the device.
  • Before servicing the fixture, disconnect power and allow time for it to cool.
  • Use care when handling the fixture. Do not expose the device to chemicals or other substances which may be corrosive.
  • Never soak or submerge the fixture in water.

Installation Instructions

  • First, identify the location where the lighting fixture will be installed.
    • Verify there are no obstructions in the area including beams, pipes, electrical wires, studs, etc.
  • Secure the fixture using appropriately rated screws or drywall anchors.
  • At this point, run your wire from the DMX decoder (or other control device) to the first fixture. Multiple fixtures can be linked together using a single home-run wire.
    • The longer the run, the thicker or lower gauge wire is recommended to help prevent voltage drop.
    • You will need a cable with 5 wires if leveraging all Red, Green, Blue, and White LEDs (plus one for power).
  • Wires can be joined using any suitable appropriate for the gauge wire such as: dolphin connectors, butt connectors, crimp connectors or even soldering. If installing outdoors, use appropriate water-tight connections that will not corrode when exposed to water.
  • Apply power and test that you now have control. If certain colors do not seem to work, verify you have a solid connection.

Wiring Color Code

Spot Light Wire Color Code

Brown Wire = Red LED Color

Green/Yellow Wire = Green LED Color

Black Wire = 24v Power Positive +

Grey Wire = 3000K White LED Color

Blue Wire = Blue LED Color

Reviews

There are no reviews yet.

Be the first to review “Axion RGBW LED Spot Lights”

Your email address will not be published. Required fields are marked *

Related products

Shopping Cart