Axion RGBW LED Recessed Downlight

$17.00$33.00

NEW VERSION AVAILABLECheck out our V2 units with 3 year warranty and other enhancements.

RGBW LED high efficiency recessed in-ceiling fixtures controllable using our DMX Controller, DMX Decoder or any 24V/12V compatible product.

If you’re looking for compatible cut-hole templates, we’ve got those too.

SKU: N/A Category:

NEW VERSION AVAILABLE – Check out our V2 units with 3 year warranty and other enhancements.

The Axion Lighting RGBW downlight series finally gives you full control over all colors in a living space with a single fixture. Why limit yourself to a single white color in your normal ceiling lights? Leveraging this fixture and our robust DMX Controller along with DMX Decoders you can create a whole house system that is low voltage, dimmable, easily integrates with popular control system platforms, and gives you millions of colors and temperatures to set the perfect ambiance. 

Installation is simple and can be used in a new-construction or retrofit scenario. Simply connect the RGBW color wires to your DMX LED Decoder like you would any other linear light strip. 

The best part of our 12/24-volt system is that it’s low voltage so you don’t have to be an electrician to install! 

6″ Indoor Specifications:

  • 24 Volt
  • 36 Watt
  • Lumen: Red – 450, Green – 360, Blue – 225, White – 945
  • White Temperature: 6000K
  • Size: 180mm x 48mm tall
  • Cut Hole: 165mm
  • Beam Angle: 100 degrees
  • Lifetime: 40,000 hours
  • Warranty: 1 year
  • IP33 Rated – Protected from tools and wires greater than 2.5 mm. Protected from water spray less than 60 degrees from vertical. 

4″ Indoor Specifications:

  • 12 Volt
  • 12 Watt
  • White Temperature: 6000K
  • Size: 120mm x 48mm tall
  • Cut Hole: 105mm
  • Beam Angle: 100 degrees
  • Lifetime: 40,000 hours
  • Warranty: 1 year
  • IP33 Rated – Protected from tools and wires greater than 2.5 mm. Protected from water spray less than 60 degrees from vertical.

2″ Indoor Specifications:

  • 24 Volt
  • 4 Watt
  • White Temperature: 6000K
  • Size: 68mm x 47mm tall
  • Cut Hole: 55mm
  • Beam Angle: 100 degrees
  • Lifetime: 40,000 hours
  • Warranty: 1 year
  • IP33 Rated – Protected from tools and wires greater than 2.5 mm. Protected from water spray less than 60 degrees from vertical.
Weight N/A
Dimensions N/A
Size

6" 24V Indoor, 2" 24V Indoor, 4" 12V Indoor, 3" 24V Outdoor

Installation Instructions

Installation Requirements

  • Before you begin installation, please verify that 24-volt power is off. It is recommended you disconnect the power supply before starting.
  • When installing in a ceiling, it is highly recommended you do not cover the top of the fixture with insulation. It is ok for it to be surrounded by insulation, but adequate airflow will ensure the heat sync can cool the fixture and provide better longevity and performance.
  • To help create a better seal between the fixture and drywall, installation of a vapor barrier prior can help reduce air entering/leaving the attic.
  • Although this document does not cover the power supply or system integration, it is worth noting that all dimming happens on the DC output side and these low voltage fixtures should not be hooked up to a 120V or 220V dimmer.
  • Do not hold the fixture by the RGBW+ cable.
  • Please check the contents of the package before installation for damage.
  • We recommend bench testing before installation.
  • ALL WIRING AND INSTALLATION SHOULD ADHERE TO LOCAL AND NATIONAL WIRING STANDARDS.

Safety

  • The fixture is 24VDC; connecting it to 12VDC, 120/240/220 AC will void the warranty and cause permanent damage.
  • Do not wire the fixture into a DMX decoder or power supply that is energized.
  • All dimming happens on the 24V side and should be done with a compatible PWM device.
  • Do not install in an environment that is fully sealed. The heat sink must have airflow to properly cool the device.
  • Do not install in environments that constantly see humidity levels above 70%.
  • Before servicing the fixture, disconnect power and allow time for it to cool.
  • Use care when handling the fixture. Do not expose the device to chemicals or other substances which may be corrosive.
  • Never soak or submerge the fixture in water.

Installation Instructions

  • First, identify the location where the lighting fixture will be installed.
    • Verify there are no obstructions above the area including beams, pipes, electrical wires, studs, etc.
  • Cut out the provided template from the top of the shipping box and trace the cut-out hole on the ceiling.
  • Using a drywall saw or other suitable device, cut out the installation hole.
  • At this point, run your wire from the DMX decoder (or other control device) to the first fixture. Multiple fixtures can be linked together using a single home-run wire.
    • The longer the run, the thicker or lower gauge wire is recommended to help prevent voltage drop.
    • You will need a cable with 5 wires if leveraging all Red, Green, Blue, and White LEDs (plus one for power).
  • Wires can be joined using any suitable appropriate for the gauge wire such as: dolphin connectors, butt connectors, crimp connectors or even soldering.
  • Once the wires have been properly joined, place the fixture into the ceiling.
  • Push up on the spring flanges so they extend up towards the heat sink, then carefully work the light into the hole. Once inside the cut-out hole, release the spring flanges and it will fully seat.
  • Apply power and test that you now have control. If certain colors do not seem to work, verify you have a solid connection.

Reviews

There are no reviews yet.

Be the first to review “Axion RGBW LED Recessed Downlight”

Your email address will not be published. Required fields are marked *

Shopping Cart